Are you tired of dealing with a faulty flush valve on your American Standard toilet?
Don’t worry, you don’t have to call a plumber just yet. With a little bit of know-how and some basic tools, you can easily replace the flush valve yourself.
In this article, we’ll guide you through the step-by-step process of changing the flush valve on your American Standard toilet.
So, grab your wrench and let’s get started!
How To Change Flush Valve On American Standard Toilet
Step 1: Turn off the water supply
Before you start working on your toilet, make sure to turn off the water supply. You can usually find the shut-off valve behind or near the toilet.
Step 2: Remove the tank from the bowl
To access the flush valve, you’ll need to remove the tank from the bowl. Start by disconnecting the water supply line from the bottom of the tank. Then, remove any bolts or screws that are holding the tank in place and carefully lift it off of the bowl.
Step 3: Remove the old flush valve
Locate the flush valve inside the tank. It will be connected to the trip lever by a beaded chain. Use pliers to remove the hair pin and clevis pin that hold the chain in place. Then, remove any clips or nuts that are securing the flush valve to the tank.
Step 4: Install the new flush valve
Take your new flush valve and insert it into the hole where you removed the old one. Make sure it is securely in place before moving on to the next step.
Step 5: Reattach the chain and clips
Reattach the beaded chain to the trip lever using the clevis pin and secure it with a hair pin. Then, reattach any clips or nuts that were removed earlier.
Step 6: Reinstall the tank
Carefully lower the tank back onto the bowl and secure it with bolts or screws. Reconnect the water supply line to the bottom of the tank.
Step 7: Turn on the water supply
Finally, turn on the water supply and let your toilet fill up with water. Test out your new flush valve by flushing a few times to make sure everything is working properly.
Congratulations! You have successfully changed out your old flush valve for a new one. With a little bit of patience and some basic tools, you can save yourself time and money by doing this simple repair yourself.
Identify The Problem With Your Flush Valve
If you are experiencing issues with your toilet not flushing properly, the problem could be with your flush valve. There are a few common problems that can occur with a flush valve over time. One issue is wear and tear on the handle assembly, which can cause the valve to not flush at all. Another issue can be a damaged relief valve, which may need to be replaced.
If the handle is not working properly, there are a few things you can check. First, make sure that the control stop or main valve supply is open. If they are closed, open them to allow water to flow to the tank. If the handle still doesn’t work, it could be due to a weak or broken part of the flushing apparatus or a chain that has come undone. In this case, you can reach into the tank and reattach the chain or adjust the nut that holds the handle in place.
If none of these solutions work and your flush valve is beyond repair, you will need to replace it. To do this, follow the steps outlined above in “How To Change Flush Valve On American Standard Toilet.” By identifying and addressing issues with your flush valve, you can ensure that your toilet is functioning properly and efficiently.
Gather The Necessary Tools And Materials
Before you start changing the flush valve on your American Standard toilet, make sure you have all the necessary tools and materials. Here’s what you’ll need:
1. Adjustable pliers – You’ll need these to remove the hair pin and clevis pin that hold the chain in place.
2. Screwdriver – Depending on the type of bolts or screws holding the tank in place, you may need a Phillips head or flathead screwdriver.
3. New flush valve – Make sure to purchase a flush valve that is compatible with your American Standard toilet model.
4. Hair pin – This small, U-shaped pin is used to secure the clevis pin in place.
5. Clevis pin – This is the pin that connects the beaded chain to the trip lever.
6. Clips or nuts – These are used to secure the flush valve to the tank.
7. Towel or rag – You’ll want to have something nearby to wipe up any water that may spill during the repair process.
By gathering these tools and materials ahead of time, you’ll be well-prepared to tackle this DIY project and get your toilet flushing like new again.
Turn Off The Water Supply And Drain The Tank
Before you start working on your toilet, it is important to turn off the water supply and drain the tank. This will prevent any water from flowing into the tank while you are working on it and make the process easier overall.
To turn off the water supply, locate the shut-off valve behind or near the toilet. Twist the handle clockwise until it stops to shut off the water supply. If you are unsure which valve controls the water supply to your toilet, you can shut off the main water supply valve for your home.
Next, you will need to drain the tank. Attach a garden hose to the drain faucet located at the bottom of the tank. Run the other end of the hose to a lower location where hot or rusty water will not cause damage. Open the drain faucet on the water heater and let all of the water drain out of the tank.
Once you have turned off the water supply and drained the tank, you can proceed with removing the tank from the bowl and replacing the flush valve. Following these steps will ensure that your repair process goes smoothly and without any complications.
Install The New Flush Valve
Now that you have removed the old flush valve, it’s time to install the new one. Follow these steps to ensure a proper installation:
Step 1: Insert the new flush valve
Take your new flush valve and insert it into the hole where you removed the old one. Make sure it is securely in place before moving on to the next step.
Step 2: Reattach the chain and clips
Reattach the beaded chain to the trip lever using the clevis pin and secure it with a hair pin. Then, reattach any clips or nuts that were removed earlier.
Step 3: Tighten the bolts
Using new brass tank hold-down bolts, tighten them just enough to compress the tank’s soft rubber gasket and keep it from leaking. Use caution not to overtighten, as this can cause damage to the tank or bowl.
Step 4: Connect the water supply
Reconnect the water supply line to the bottom of the tank. Make sure it is securely attached and turn on the water supply.
Step 5: Test your new flush valve
Finally, test out your new flush valve by flushing a few times to make sure everything is working properly. Check for any leaks or issues with flushing.
By following these steps, you can easily install a new flush valve on your American Standard toilet. Remember to always turn off the water supply before starting any repairs and follow all safety precautions.